A book slipcase is a rigid enclosure with one open face. In the five-panel construction described here, the books enter fore-edge first, leaving their spines facing the opening.
The choice between a book slipcase and rigid box establishes the enclosure type. Slipcase sizing then determines how the finished books fit inside it.
The structure consists of two large side panels, a top wall, a bottom wall and a closed rear wall. The side panels sit parallel to the book covers; the rear wall sits behind the fore-edges.
The assembled panels must remain square. Unequal wall widths or inward-bowing side panels can restrict the opening even when the nominal dimensions are correct.
Confirm the book board thickness before calculating the panel sizes, keeping the wall thickness separate from the usable space inside.
Printed paper or book cloth covers the board structure and turns around the opening.
A smooth inner lining covers exposed board and joints. Its edges should remain firmly attached, without ridges or lifted corners in the sliding path.

Measure the bound book rather than its trim size, which describes the interior pages rather than the complete cover.
Fit any dust jacket before measuring, so its folds and finished surface are included.
Close the book naturally without squeezing it. On a flat surface, use a steel ruler and square blocks to check the height, cover-to-cover thickness and spine-to-fore-edge depth.
Take readings at several points, retain the largest measurement in each direction and record to the nearest 0.5 mm where practical. Check thickness at both the spine and fore-edge rather than relying on the printed spine specification.
Check several finished copies to capture normal binding variation. A tightly pressed sample can underestimate the space needed by the rest of the edition.
For a multi-volume set, arrange the actual books together in their final order and measure the group without compression. Use this combined thickness rather than adding calculated spine widths.
The tallest and deepest volumes establish the other two dimensions. Smaller volumes must also be tested: a case that fits the largest book can still leave another volume insufficiently supported.
Use consistent dimension names on the drawing. The internal dimensions below refer to the completed, lined cavity, not the outside of the case.
| Dimension | Measurement Basis |
|---|---|
| Internal height | Maximum finished book height plus total vertical clearance |
| Internal capacity | Maximum book or grouped-set thickness plus total sliding clearance |
| Internal depth | Full finished cover depth plus any specified spine recess |
For an initial five-panel mock-up using 2 mm board, a bare-board cavity with 2 mm added to the book height and 2 mm added to its thickness provides a reference starting point.
The lining and opening turn-ins consume part of those allowances. They are not 2 mm of finished free clearance, nor are they bulk-production tolerances.
An allowance applies to the total dimension. Adding 2 mm to height provides approximately 1 mm above and below a centred book, not 2 mm on each edge.
Set the depth against the intended opening position. For a fully contained book, measure from the outer cover edge at the fore-edge to the furthest point of the spine, including a rounded spine.
If the spine is to sit recessed, add that recess to the internal depth. Mark the position on the drawing instead of assuming that the height allowance should also be applied in this direction.

Add the lining build-up to the required finished cavity before calculating the board shell. For example, two opposing lining layers measuring 0.15 mm each occupy 0.3 mm of the available space.
Overlapping material around the opening can be thicker than the lining farther inside. Size the entry around that local build-up; do not rely only on a measurement taken deep inside the empty case.
Once the bare-board cavity is established, add the surrounding wall thicknesses. With single 2 mm walls, the shell adds 4 mm to height, 4 mm to capacity and 2 mm to depth because the opening has no closing wall.
The outer covering adds to the final external dimensions. If the construction uses doubled top or bottom walls, count their actual thickness rather than applying the single-wall calculation.
The unprinted structural sample should use the intended board, lining and wrapping material, with the opening fully turned in. Test the actual books only after the adhesive has dried.
Slide the books through the complete insertion path. Resistance only at the entrance indicates a different problem from pressure along the entire side panel. Check the turned edges, squareness and panel bowing before enlarging the cavity.
Top-and-bottom pressure calls for a height correction; pressure against the covers calls for a capacity correction. Insufficient depth leaves the spine projecting beyond its specified position.
After adjustment, test both the largest measured copy or set and a smaller one. The books should enter and withdraw without scraping, forced compression or excessive movement inside the case.
Contanct
Related Keywords
Coated Paper for PrintingPantone Color for PrintingTrim Size for Book PrintingPrepress Artwork for Book PrintingUncoated Book PaperExhibition Promotional Spiral Notebook Printing ServiceRecycled Paper for PrintingCustom Spiral Notebook Printing with Embossed LogosGutter for Book PrintingVector Graphics for Book PrintingSupported File Formats for Book PrintingBinding Margin for PrintingSpot UV PrintingBook Cloth for Hardcover CoversFacing Pages for Book PrintingPage Margins For PrintingImage Resolution for Book PrintingCustom Spiral Notebooks for Gift ShopsPaper Weight for Book Printing: GSM and LBCustom Spiral Notebook Printing for SchoolsCrop Marks for PrintingFlexibound BindingLamination for PrintingBranded Spiral Notebooks for CompaniesPlastic Coil Notebook Printing SupplierTotal Ink Coverage in PrintingSinger Sewn BindingFont Embedding for Book PrintingKraft Paper for PrintingFlat Size for Book PrintingOverprint in PrintingSafe Area for PrintingPaper Grain Direction for Book BindingPrint-Ready Files for Book PrintingBook Slipcase Construction and SizingSpiral and Wire-O BindingCustom Spiral Notebook Printing for Wedding FavorsBook Printing File Preparation ChecklistHeadbands and Ribbon BookmarksTwo-Page Spreads for Book PrintingFold Lines for Book PrintingVarnish and Coating for PrintingFonts and Outlines for Book PrintingCustom Spiral Notebooks for Stationery BrandsBook Closures and Accessories